MultiRAE P2P by Honeywell RAE Systems - Multigas Monitor
Training
Available
Available
Training
MultiRAE P2P by Honeywell RAE Systems - Multigas Monitor
Cross-sensitivity warning: This instrument may react to gases beyond its primary target. Check the spec sheet to verify compatibility with your gas mixture before use.
This unit comes standard with PID, CO, O₂, H₂S, and LEL sensors. All other sensors are available upon request.
The MultiRAE P2P by Honeywell RAE Systems is a pumped multigas monitor with Point-to-Point wireless capability and Thiamis connectivity for remote datalogging in industrial and environmental monitoring applications. This 5-gas configuration measures CO from 0–500 ppm (1 ppm resolution), H₂S from 0–100 ppm (0.1 ppm resolution), O₂ from 0–30% Vol. (0.1% Vol. resolution), combustibles from 0–100% LEL (1% LEL resolution), and VOCs via PID (choice of either HIGH or LOW resolution sensor). Compatible with Honeywell Safety Suite Device Configurator Software for configuration, datalogging, and compliance reporting.
Choose Your Option
Rent for flexible short-term use or purchase to own
Rental Rates
Daily
$140.00
Weekly
$410.00
Monthly
Contact for pricing
Reference rates only. You get the best rate calculation - actual price based on your selected rental dates.
What is the MultiRAE P2P used for?
It's a MultiRAE configuration with point-to-point (P2P) capability for remote monitoring and connected workflows — used when you need readings and alarms beyond line-of-sight, such as distributed work zones, large sites, or supervisor visibility into multiple crews.
What gases does this P2P configuration measure?
CO (0–500 ppm), H2S (0–100 ppm), O2 (0–30% vol.), LEL (0–100%), and VOC via PID (0–5,000 ppm, 0.1 ppm resolution) — a 5-gas configuration.
Is this unit intrinsically safe?
This item is not configured as intrinsically safe. Confirm site classification requirements before deployment.
Why use a connected/P2P monitor instead of a standalone unit?
Connected monitoring helps when you need centralized oversight, alarm visibility across a site, or recordkeeping across multiple users. It doesn't replace a hazard assessment — sensor selection, placement, and response procedures still determine whether monitoring is effective.
What should I confirm before using it for confined space or permit work?
Confirm the sensor set matches the permit hazards, that the unit is appropriate for the site classification, and your pre-use verification procedure and documentation workflow.
What's included with the rental kit?
The monitor plus chargers, alkaline battery pack, calibration cap, tools, PID removal tool, spare charcoal filters, mini USB cable, spare pump filter, and Safety Suite software on a flash drive.
How much does it cost to rent the MultiRAE P2P?
Listed rental rates are $140/day and $410/week. Pricing beyond two weeks is quoted — contact RAECO Rents.
Exposure Hazards This Equipment Detects
Carbon Monoxide (CO)
CAS:
630-08-0
Learn More
Updated on March 17, 2026
PEL TWA
50 ppm (55 mg/m³)
REL TWA
35 ppm (40 mg/m³)
TLV TWA
N/A
Chlorine Gas (Cl₂)
CAS:
7782-50-5
Learn More
Updated on March 17, 2026
PEL TWA
1 ppm (3 mg/m³) [Construction and Maritime Industries only]
REL TWA
N/A
TLV TWA
0.1 ppm (0.29 mg/m³)
Formaldehyde (CH₂O)
CAS:
50-00-0
Learn More
Updated on March 17, 2026
PEL TWA
0.75 ppm [0.5 ppm Action Level]
REL TWA
0.016 ppm
TLV TWA
0.1 ppm [2016]
Hydrogen Sulfide (H₂S)
CAS:
7783-06-4
Learn More
Updated on March 17, 2026
PEL TWA
N/A
REL TWA
N/A
TLV TWA
1 ppm [2009]
Nitrogen Dioxide (NO₂)
CAS:
10102-44-0
Learn More
Updated on March 17, 2026
PEL TWA
N/A
REL TWA
N/A
TLV TWA
0.2 ppm (0.38 mg/m³)
Sulfur Dioxide (SO₂)
CAS:
7446-09-5
Learn More
Updated on March 09, 2026
PEL TWA
5 ppm (13 mg/m³)
REL TWA
2 ppm (5 mg/m³)
TLV TWA
N/A
Volatile Organic Compounds (VOCs)
CAS:
N/A
Learn More
Updated on March 09, 2026
PEL TWA
N/A
REL TWA
N/A
TLV TWA
N/A
Lower Explosive Limit (LEL)
CAS:
N/A
Learn More
Updated on March 09, 2026
PEL TWA
N/A
REL TWA
N/A
TLV TWA
N/A
Nitric Oxide (NO)
CAS:
10102-43-9
Learn More
Updated on March 09, 2026
PEL TWA
25 ppm (30 mg/m³)
REL TWA
25 ppm (30 mg/m³)
TLV TWA
25 ppm [1992]
Hydrogen (H₂)
CAS:
1333-74-0
Learn More
Updated on March 09, 2026
PEL TWA
N/A
REL TWA
N/A
TLV TWA
N/A
Ethylene Oxide (C₂H₄O)
CAS:
75-21-8
Learn More
Updated on March 17, 2026
PEL TWA
1 ppm [0.5 ppm Action Level]
REL TWA
<0.1 ppm (<0.18 mg/m³)
TLV TWA
1 ppm [1990]
Ammonia (NH₃)
CAS:
7664-41-7
Learn More
Updated on April 10, 2026
PEL TWA
50 ppm (35 mg/m³)
REL TWA
25 ppm (18 mg/m³)
TLV TWA
25 ppm (17 mg/m³)
Oxygen (O₂)
CAS:
7782-44-7
Learn More
Updated on March 09, 2026
PEL TWA
N/A
REL TWA
N/A
TLV TWA
N/A
Methane (CH₄)
CAS:
74-82-8
Learn More
Updated on March 09, 2026
PEL TWA
No established PEL
REL TWA
No established REL
TLV TWA
No established TLV
Chlorine Dioxide (ClO₂)
CAS:
10049-04-4
Learn More
Updated on April 29, 2026
PEL TWA
0.1 ppm (0.3 mg/m³)
REL TWA
0.1 ppm (0.3 mg/m³)
TLV TWA
0.1 ppm (0.28 mg/m³)
Features & Capabilities
| Calibration Certificate Available: | ✓ Yes |
| Datalogging: | ✓ Yes |
| Monitoring Scope: | Personal Monitoring |
Equipment Specifications
| Component Role: | Base instrument — accepts up to five interchangeable sensors simultaneously, or six gases when the CO+H2S combo sensor is fitted. Commonly supplied as a five-gas configuration (PID, CO, O2, H2S and LEL); all sensors below are selectable |
| Sensor-Dependent Specifications: | Target gases, measurement ranges and resolutions are determined entirely by which sensors are fitted. See the interchangeable module specifications below. |
| Detection Method / Sensor Type: | Intelligent interchangeable field-replaceable sensors — PID for VOCs, electrochemical for toxic gases and oxygen, and catalytic for combustibles. Sensors store their own calibration data and can be swapped in the field |
| Relative Humidity Range: | 0% to 95% RH, non-condensing |
| Sample Flow Rate: | Built-in pump, average 250 cc/min, with automatic shutoff in low-flow conditions |
| Alarm Features: | Multi-tone audible (95 dB at 30 cm), vibration, flashing bright red LEDs and on-screen indication, plus wireless remote alarm notification; Man Down alarm with pre-alarm |
| Calibration Method: | Zero, span and bump calibration; automatic with AutoRAE 2 or manual |
| Connectivity: | Point-to-Point wireless plus hardwired P2P serial connection to a Thiamis 4G gateway for remote datalogging to the Environet cloud platform. PC setup and data download via charging/PC communication cradle or AutoRAE 2; compatible with Honeywell Safety Suite Device Configurator software |
| Display: | Monochrome graphical LCD (128 x 160) with backlighting and automatic screen flip; shows real-time gas concentrations, PID measurement gas and correction factor, battery status, datalogging and wireless status, plus STEL, TWA, peak and minimum values |
| Operating Temperature Range: | -4°F to 122°F (-20°C to 50°C) |
| Water/Dust Ingress Rating: | IP-65 |
| Intrinsically Safe Rating: | CSA: Class I, Division 1, Groups A, B, C and D, T4. ATEX: 0575 II 2G Ex ia d IIC T4 Gb. IECEx: Ex ia d IIC T4 Gb |
| Data Logging Interval: | User-configurable, 1 to 3,600 seconds |
| Data Storage Capacity: | Continuous datalogging — 6 months for 5 sensors at 1-minute intervals, 24/7 |
| Battery Run Time: | Rechargeable Li-ion approx. 12 hours (recharge under 6 hours); extended-duration Li-ion approx. 18 hours (recharge under 9 hours); alkaline adapter with 4x AA approx. 6 hours |
| Size / Weight: | 7.6 x 3.8 x 2.6 in (193 x 96.5 x 66 mm); 31 oz (880 g) |
| Regulatory Certifications: | EMC Directive 2004/108/EC, R&TTE Directive 1999/5/EC, ATEX Directive 94/9/EC |
| Compliance Standards: | CSA C22.2 No. 152 (LEL), ISA-12.13.01 (LEL) |
Interchangeable Module Specifications
Key specifications are determined by which of the 21 modules below is fitted. Select one when configuring your rental. Expand any module to view its specifications.
Volatile Organic Compounds (VOCs)
Photoionization detector (PID), 10.6 eV lamp — high resolution
Range
0 to 5,000 ppm
Resolution
0.1 ppm
Response
T90 < 15 seconds (isobutylene)
Operating Temp
-20°C to 50°C (MultiRAE family)
Volatile Organic Compounds (VOCs)
Photoionization detector (PID), 10.6 eV lamp — standard resolution
Range
0 to 1,000 ppm
Resolution
1 ppm
Response
T90 < 15 seconds (isobutylene)
Operating Temp
-20°C to 50°C (MultiRAE family)
Chlorine (Cl2)
Electrochemical
Range
0 to 50 ppm
Resolution
0.1 ppm
Operating Temp
-20°C to 50°C (MultiRAE family); -20°C to 55°C (ToxiRAE Pro)
Carbon Monoxide (CO)
Electrochemical
Range
0 to 500 ppm
Resolution
1 ppm
Operating Temp
-20°C to 50°C (MultiRAE family); -20°C to 55°C (ToxiRAE Pro)
Carbon Monoxide (CO), hydrogen-compensated
Electrochemical with hydrogen compensation
Range
0 to 2,000 ppm
Resolution
10 ppm
Operating Temp
-20°C to 50°C (MultiRAE family); -20°C to 55°C (ToxiRAE Pro)
Carbon Monoxide (CO) + Hydrogen Sulfide (H2S)
Electrochemical (dual-element)
Range
CO: 0 to 500 ppm; H2S: 0 to 200 ppm
Resolution
CO: 1 ppm; H2S: 0.1 ppm
Operating Temp
-20°C to 50°C (MultiRAE family)
Ethylene Oxide (EtO-A)
Electrochemical
Range
0 to 100 ppm
Resolution
1 ppm
Operating Temp
-20°C to 50°C (MultiRAE family); -20°C to 55°C (ToxiRAE Pro)
Hydrogen (H2)
Electrochemical
Range
0 to 1,000 ppm
Resolution
2 ppm
Operating Temp
-20°C to 50°C (MultiRAE family); -20°C to 55°C (ToxiRAE Pro)
Hydrogen Sulfide (H2S)
Electrochemical
Range
0 to 100 ppm
Resolution
0.1 ppm
Operating Temp
-20°C to 50°C (MultiRAE family); -20°C to 55°C (ToxiRAE Pro)
Formaldehyde (HCHO)
Electrochemical
Range
0 to 10 ppm
Resolution
0.01 ppm
Operating Temp
-20°C to 50°C (MultiRAE family); -20°C to 55°C (ToxiRAE Pro)
Hydrogen Cyanide (HCN)
Electrochemical
Range
0 to 50 ppm
Resolution
0.5 ppm
Operating Temp
-20°C to 50°C (MultiRAE family); -20°C to 55°C (ToxiRAE Pro)
Combustible gases (% LEL)
Catalytic bead
Range
0 to 100% LEL
Resolution
1% LEL
Response
T90 < 15 seconds
Operating Temp
-20°C to 50°C (MultiRAE family)
Ammonia (NH3)
Electrochemical
Range
0 to 100 ppm
Resolution
1 ppm
Operating Temp
-20°C to 50°C (MultiRAE family); -20°C to 55°C (ToxiRAE Pro)
Nitric Oxide (NO)
Electrochemical
Range
0 to 250 ppm
Resolution
0.5 ppm
Operating Temp
-20°C to 50°C (MultiRAE family); -20°C to 55°C (ToxiRAE Pro)
Nitrogen Dioxide (NO2)
Electrochemical
Range
0 to 20 ppm
Resolution
0.1 ppm
Operating Temp
-20°C to 50°C (MultiRAE family); -20°C to 55°C (ToxiRAE Pro)
Oxygen (O2)
Electrochemical
Range
0 to 30% Vol.
Resolution
0.1% Vol.
Operating Temp
-20°C to 50°C (MultiRAE family)
Phosphine (PH3)
Electrochemical
Range
0 to 20 ppm
Resolution
0.1 ppm
Operating Temp
-20°C to 50°C (MultiRAE family); -20°C to 55°C (ToxiRAE Pro)
Sulfur Dioxide (SO2)
Electrochemical
Range
0 to 20 ppm
Resolution
0.1 ppm
Operating Temp
-20°C to 50°C (MultiRAE family); -20°C to 55°C (ToxiRAE Pro)
Chlorine Dioxide (ClO2)
Electrochemical
Range
0 to 1 ppm
Resolution
0.03 ppm
Operating Temp
-20°C to 50°C (MultiRAE family); -20°C to 55°C (ToxiRAE Pro)
Thiamis 4G by Aethair - IoT Communications Device
Operating Temp
-30°C to 75°C (-22°F to 167°F)
Battery
None — the Thiamis 4G has no onboard battery. It operates on continuous external power (12VDC or USB-C).
Lufft WS500-UMB Smart Weather Station
Measures
Air Temperature, Relative Humidity, Barometric Pressure, Wind Speed, Wind Direction
Kit Contents
Manufacturer Resources
Documents
User manuals, safety guides, and technical documentation from the manufacturer:
Videos
No manufacturer videos are currently available for this product. Check back later or contact us for more information.
Ask a Question
Have a question about this product? Fill out the form below and our team will get back to you shortly.
- Translation missing: en.general.accessibility.refresh_page
- Translation missing: en.general.accessibility.new_window
Rental Dates Notice